your Local licensed and insured neighbourhood electricians
Emergency Service
Electrical work can feel overwhelming, especially when you’re not sure where to start or what’s actually involved. That’s where we come in. We’re your local, licensed, and insured Calgary electricians, ready to tackle everything from a simple service call to a full renovation wiring project.
If your panel is outdated, undersized, or tripping breakers more often than it should, we start with an onsite assessment of your current service and what your home actually draws. We then walk you through the right panel size for your household and pull the required electrical permit. Most panel jobs are done in a single day, and we coordinate the utility disconnect so you’re without power for as short a window as possible, with every job inspected and labelled before we call it done.
We install dedicated EV charging circuits so you can plug in at home overnight instead of hunting for a public station. The job starts with confirming your panel has the capacity for a new 240-volt circuit, and if it doesn’t, we’ll talk through whether a small panel upgrade makes sense. A straightforward install with existing capacity is usually a half-day job, and we make sure the finished work meets permit and inspection requirements. If you’re in Calgary, it’s worth checking whether the ChargeYYC rebate program applies to your installation.
Under cabinet lighting is a small change that makes a noticeable difference in how a kitchen feels to use. We plan the wiring around your cabinet layout so the fixtures sit flush and stay out of sight, then connect them to a switch location that actually makes sense for how you cook. The result is a brighter counter and a kitchen that looks finished, not something bolted on afterward. It’s a quick addition during a renovation, and just as straightforward to retrofit into a kitchen that’s already built.
Pot lights change the whole feel of a room, but the result depends on getting the layout right before any cutting starts. We map out spacing and placement based on your ceiling height and room size, then handle the wiring and finishing so everything lines up evenly. It looks like a simple upgrade from the outside, though the planning up front is what keeps you from ending up with lights in awkward spots. We also account for existing joists and insulation, so the finished ceiling looks intentional rather than uneven.
If your current lighting is outdated, dim, or costing more to run than it should, we’ll walk you through options that actually fit how you use the space. That might mean swapping old fixtures for something more efficient, or it might mean rewiring a room that’s never had enough coverage to begin with. Either way, we handle the electrical side of the upgrade so the new lighting works properly and safely from day one. We’ll also flag any switches or wiring that don’t meet current code while we’re in there.
When you’re renovating, your electrical needs to keep pace with the new layout, not just get patched around it. We plan circuits for the finished space before drywall goes up, and make sure every run is sized to Alberta code. Since renovation wiring is inspected before it’s closed in, we schedule our rough-in around your contractor’s timeline so we’re never the reason your project stalls. Whether it’s one room or a full main-floor gut, we’ll give you a clear scope before we start.
Hot tubs need a dedicated, GFCI-protected circuit sized to the heater, along with a disconnect switch installed within sight of the unit, and that’s not something to guess at or wire yourself. We size the circuit to your specific tub and run the wiring to code, then install the disconnect switch exactly where it belongs so the whole setup passes inspection without issues. Once it’s connected, you’re not left wondering whether it’s actually safe to use. We coordinate timing with your hot tub delivery so the electrical is ready before it arrives.
Central air only works as well as the electrical behind it, so we make sure your A/C unit is wired on a properly sized, dedicated circuit from the start. That means no tripped breakers on the hottest day of summer and no guessing whether the unit is pulling more than the circuit was built to handle. We coordinate with your HVAC installer where needed so the electrical and mechanical sides of the job line up without delays. Older homes sometimes need a panel assessment first to confirm there’s enough capacity for the new unit.
Landscape lighting has to hold up to Alberta’s weather while still looking good, so we design and wire systems built for both. We plan pathway and feature lighting around how you actually use your yard, then run the wiring below grade and connect it to a transformer sized for the whole system. The result is lighting that turns on reliably through the seasons instead of flickering out after the first cold snap. We can also tie new lighting into an existing system if you’re adding on rather than starting from scratch.
Electrical problems don’t wait for a convenient time, so we keep room in our schedule for both routine service calls and urgent ones. Regular requests are typically booked within three days, and if something’s actively unsafe, like a breaker that won’t reset or an outlet that’s warm to the touch, we move faster to get someone to your door. Either way, you’re getting a licensed electrician who diagnoses the actual problem instead of guessing at a fix. Our trucks carry the parts needed for most common repairs, so a second visit is rarely necessary.
Water and electricity don’t mix, and a flooded basement means your electrical system needs a proper assessment before anything gets used again. If your panel, outlets, or wiring have been exposed to water, don’t plug anything in or try to reset a breaker yourself. We’ll check what’s been affected, and a panel that’s taken on water typically needs to be replaced rather than dried out and reused. Once repairs are made, the work goes through inspection before we reconnect power, so you know the system is genuinely safe.
When you call us, you get a team that shows up when we say we will and stands behind every job we complete. Our trucks are stocked for most residential service calls, so there’s no waiting around for parts or a return visit. We work cleanly, inspect our own work before we call a job finished, and make sure everything is up to code before we head out. Getting your home’s electrical sorted should be straightforward, and with us, it is.
Yes. Electrical problems don’t wait for a convenient time, which is why we offer emergency service on top of our regular three-day response window for standard calls.
Often, yes, though it depends on how much spare capacity your existing panel has. We’ll check your service size first and let you know if a small panel upgrade needs to happen alongside the charger install.
Most panel upgrades are completed in a single day. A full service size increase with a new meter base can take longer depending on your home’s existing setup, and we’ll give you a realistic timeline before we start.
Yes. Alberta requires an electrical permit and a Safety Codes Officer inspection for panel work and most new circuits. We pull the permit and schedule the inspection as part of the job.
Don’t enter the space or touch anything electrical. Get the power shut off and call us to assess the damage before anything is reconnected or reused.
Yes. Hot tubs need a dedicated, GFCI-protected circuit sized to the heater, along with a disconnect switch installed within sight of the tub. It’s a code requirement, not an optional upgrade.
We do. Whether it’s a single service call or wiring a full renovation from the studs out, we scope the job the same way: a clear plan, a permit where one’s required, and an inspection before we call it done.
